pyHydrabus package¶

Submodules¶

pyHydrabus.hydrabus module¶

class pyHydrabus.hydrabus.Hydrabus(port='')¶

Bases: object

Base class for all modes.

Manages all serial communication

close()¶: Close the serial port

connected¶

Check if serial port is opened

Returns:	Bool

enter_bbio()¶

Enter BBIO mode.

This should be done prior all further operations

Returns:	Bool

exit_bbio()¶

Reset Hydrabus to CLI mode

Returns:	Bool

flush_input()¶: Flush input buffer (data from Hydrabus)

identify()¶

Identify the current mode

Returns:	Current mode
Return type:	str

in_waiting¶

Return the number of bytes in the receive buffer.

Returns:	Number of bytes
Return type:	int

read(length=1)¶

Base read primitive

Parameters:	length (int) – Number of bytes to read
Returns:	Read data
Return type:	bytes

reset()¶

Force reset to BBIO main mode

Returns:	Bool

timeout¶

Serial port read timeout

Returns:	timeout
Return type:	int

write(data=b'')¶

Base write primitive

Parameters:	data (bytes) – Bytes to write

pyHydrabus.i2c module¶

class pyHydrabus.i2c.I2C(port='')¶

Bases: pyHydrabus.protocol.Protocol

I2C protocol handler

Example:

>>> #Read data from an EEPROM
>>> import pyHydrabus
>>> i=pyHydrabus.I2C('/dev/hydrabus')
>>> i.set_speed(pyHydrabus.I2C.I2C_SPEED_100K)
>>> i.pullup=1
>>> i.start();i.bulk_write(b' ');print(i.write_read(b'¡',64))

I2C_SPEED_100K = 1¶

I2C_SPEED_1M = 3¶

I2C_SPEED_400K = 2¶

I2C_SPEED_50K = 0¶

bulk_write(data=b'')¶

Bulk write on I2C bus https://github.com/hydrabus/hydrafw/wiki/HydraFW-Binary-I2C-mode-guide#bulk-i2c-write-0b0001xxxx

Parameters:	data (bytes) – Data to be sent
Returns:	ACK status of the written bytes (b’‘=ACK, b’’=NACK)
Return type:	list

pullup¶: Pullup status (0=off, 1=on)

read(length=0)¶

Read on I2C bus

Parameters:	length (int) – Number of bytes to read
Returns:	Read data
Return type:	bytes

read_byte()¶: Read a byte from the I2C bus

scan()¶

Scan I2C bus and returns all available device addresses in a list

Returns:	List of available device addresses
Return type:	list

send_ack()¶: Send an ACK Used with the read_byte() function

send_nack()¶: Send a NACK Used with the read_byte() function

set_speed(speed)¶

Set I2C bus speed

Parameters:	speed – Select any of the defined speeds (I2C_SPEED_*)

start()¶: Send a I2C start condition

stop()¶: Send a I2C stop condition

write(data=b'')¶

Write on I2C bus

Parameters:	data (bytes) – data to be sent

write_read(data=b'', read_len=0)¶

Write-then-read operation https://github.com/hydrabus/hydrafw/wiki/HydraFW-Binary-I2C-mode-guide#i2c-write-then-read-0b00001000

This method sends a start condition before writing and a stop condition after reading.

Parameters:	data (bytes) – Data to be sent read_len (int) – Number of bytes to read
Returns:	Read data
Return type:	bytes

pyHydrabus.onewire module¶

class pyHydrabus.onewire.OneWire(port='')¶

Bases: pyHydrabus.protocol.Protocol

One wire protocol handler

Example:

TODO

bulk_write(data=b'')¶

Bulk write on 1-Wire bus https://github.com/hydrabus/hydrafw/wiki/HydraFW-binary-1-Wire-mode-guide#bulk-1-wire-transfer-0b0001xxxx

Parameters:	data (bytes) – Data to be sent

pullup¶: Pullup status (0=off, 1=on)

read(read_len=0)¶

Read on 1-Wire bus

Return read_len:
Parameters:	read_len – Number of bytes to be read
	int
Returns:	Read data
Return type:	bytes

read_byte()¶: Read a byte from the 1-Wire bus

reset()¶: Send a 1-Wire reset

write(data=b'')¶

Write on 1-Wire bus

Parameters:	data (bytes) – data to be sent

pyHydrabus.protocol module¶

class pyHydrabus.protocol.Protocol(name='', fname='', mode_byte=b'x00', port='')¶

Bases: object

Base class for all supported protocols

Parameters:	name (str) – Name of the protocol (returned by Hydrabus) eg. SPI1 fname (str) – Full name of the protocol mode_byte (bytes) – Byte used to enter the mode (eg. for SPI) port (str) – The port name

close()¶: Close the communication channel and resets Hydrabus

hydrabus¶

Return _hydrabus instance to access Hydrabus class functions and serial methods from any protocol classes instances

Returns:	_hydrabus class instance

identify()¶

Identify the current mode

Returns:	The current mode identifier (4 bytes)
Return type:	str

timeout¶

pyHydrabus.rawwire module¶

class pyHydrabus.rawwire.RawWire(port='')¶

Bases: pyHydrabus.protocol.Protocol

Raw wire protocol handler

Example:

>>> import pyHydrabus
>>> r=pyHydrabus.RawWire('/dev/hydrabus')
>>> # Set SDA to high
>>> r.sda = 1
>>> # Send two clock ticks
>>> r.clocks(2)
>>> # Read two bytes
>>> data = r.read(2)

bulk_ticks(num)¶

Sends a bulk of clock ticks (1 to 16) https://github.com/hydrabus/hydrafw/wiki/HydraFW-binary-raw-wire-mode-guide#bulk-clock-ticks-0b0010xxxx

Parameters:	num (int) – Number of clock ticks to send

bulk_write(data=b'')¶

Bulk write on Raw-Wire https://github.com/hydrabus/hydrafw/wiki/HydraFW-binary-raw-wire-mode-guide#bulk-raw-wire-transfer-0b0001xxxx

Parameters:	data (bytes) – Data to be sent

clk¶: CLK pin status

clock()¶: Send a clock tick

clocks(num)¶

Sends a number of clock ticks

Parameters:	num (int) – Number of clock ticks to send

gpio_mode¶: Raw-Wire GPIO mode (0=Push-Pull, 1=Open Drain)

read(length=0)¶

Read on Raw-Wire bus

Parameters:	length (int) – Number of bytes to read
Returns:	Read data
Return type:	bytes

read_bit()¶: Sends a clock tick, and return the read bit value

read_byte()¶

Read a byte from the raw wire

Returns:	The read byte
Return type:	bytes

sda¶: SDA pin status

set_speed(speed)¶

Sets the clock max speed.

Parameters:	speed – speed in Hz. Possible values : TODO

wires¶: Raw-Wire mode (2=2-Wire, 3=3-Wire)

write(data=b'')¶

Write on Raw-Wire bus

Parameters:	data (bytes) – data to be sent
Returns:	Read bytes
Return type:	bytes

write_bits(data=b'', num_bits=0)¶

Write bits on Raw-Wire bus Bits are sent MSB first.

Parameters:	data (int) – data to be sent num_bits – number of bits to send
Returns:	Read bytes
Return type:	bytes

pyHydrabus.smartcard module¶

class pyHydrabus.smartcard.Smartcard(port='')¶

Bases: pyHydrabus.protocol.Protocol

Smartcard protocol handler

Example:

>>> #Read ATR from a smartcard
>>> import pyHydrabus
>>> sm=pyHydrabus.Smartcard('/dev/hydrabus')
>>> sm.prescaler=12
>>> sm.baud=9600
>>> sm.rst=1;sm.rst=0;sm.read(1)

baud¶: Baud rate

get_atr()¶: Get smartcard ATR

guardtime¶: Guard time value

prescaler¶: Prescaler value

pullup¶

read(read_len=0)¶

Read on smartard

Parameters:	read_len (int) – number of bytes to be read

rst¶: RST pin status

write(data=b'')¶

Write on smartard

Parameters:	data – data to be sent

write_read(data=b'', read_len=0)¶

Write-then-read operation https://github.com/hydrabus/hydrafw/wiki/HydraFW-binary-SMARTCARD-mode-guide#write-then-read-operation-0b00000100

Parameters:	data – Data to be sent read_len (int) – number of bytes to read

pyHydrabus.spi module¶

class pyHydrabus.spi.SPI(port='')¶

Bases: pyHydrabus.protocol.Protocol

SPI protocol handler

Example:

TODO

SPI1_SPEED_10M = 5¶

SPI1_SPEED_1M = 2¶

SPI1_SPEED_21M = 6¶

SPI1_SPEED_2M = 3¶

SPI1_SPEED_320K = 0¶

SPI1_SPEED_42M = 7¶

SPI1_SPEED_5M = 4¶

SPI1_SPEED_650K = 1¶

SPI2_SPEED_10M = 6¶

SPI2_SPEED_160K = 0¶

SPI2_SPEED_1M = 3¶

SPI2_SPEED_21M = 7¶

SPI2_SPEED_2M = 4¶

SPI2_SPEED_320K = 1¶

SPI2_SPEED_5M = 5¶

SPI2_SPEED_650M = 2¶

bulk_write(data=b'')¶

Bulk write on SPI bus https://github.com/hydrabus/hydrafw/wiki/HydraFW-Binary-SPI-mode-guide#bulk-spi-transfer-0b0001xxxx

Parameters:	data (bytes) – Data to be sent
Returns:	Bytes read during the transfer
Return type:	bytes

cs¶: Chip-Select (CS) status getter

device¶: SPI device to use (1=spi1, 0=spi2)

phase¶: SPI clock phase

polarity¶: SPI polarity

read(read_len=0, drive_cs=0)¶

Read on SPI bus

Parameters:	read_len (int) – Number of bytes to be read drive_cs (int) – Whether to enable chip select before writing/reading (0=yes, 1=no)
Returns:	Read data
Return type:	bytes

set_speed(speed)¶

Set SPI bus speed

Parameters:	speed – Select any of the defined speeds (SPI_SPEED_*)

write(data=b'', drive_cs=0)¶

Write on SPI bus

Parameters:	data (bytes) – data to be sent drive_cs (int) – Whether to enable chip select before writing/reading (0=yes, 1=no)

write_read(data=b'', read_len=0, drive_cs=0)¶

Write-then-read operation https://github.com/hydrabus/hydrafw/wiki/HydraFW-Binary-SPI-mode-guide#write-then-read-operation-0b00000100—0b00000101

Parameters:	data (bytes) – Data to be sent read_len (int) – Number of bytes to read drive_cs (int) – Whether to enable chip select before writing/reading (0=yes, 1=no)
Returns:	Read data
Return type:	bytes

pyHydrabus.Utils module¶

Utilities available in hydrafw

param port:	The port name
type port:	str

pyHydrabus.Utils.adc¶

Read ADC value

Returns:	ADC value (10 bits)
Return type:	int

pyHydrabus.uart module¶

UART protocol handler

example:	TODO

>>> #Read data from an EEPROM
>>> import pyHydrabus
>>> u=pyHydrabus.UART('/dev/hydrabus')
>>> u.baud=115200
>>> u.echo=1

pyHydrabus.UART.baud¶: Baud rate

pyHydrabus.UART.echo¶: Local echo (0=No, 1=Yes)

pyHydrabus.UART.hydrabus¶

Return _hydrabus instance to access Hydrabus class functions and serial methods from any protocol classes instances

Returns:	_hydrabus class instance

pyHydrabus.UART.timeout¶

pyHydrabus.swd module¶

SWD protocol handler

example:

>>> import pyHydrabus
>>> swd = pyHydrabus.SWD('/dev/ttyACM0')
>>> swd.bus_init()
>>> swd.read_dp(0)
>>> swd.write_dp(4, 0x50000000)
>>> swd.scan_bus()

pyHydrabus.SWD.clk¶: CLK pin status

pyHydrabus.SWD.gpio_mode¶: Raw-Wire GPIO mode (0=Push-Pull, 1=Open Drain)

pyHydrabus.SWD.hydrabus¶

Return _hydrabus instance to access Hydrabus class functions and serial methods from any protocol classes instances

Returns:	_hydrabus class instance

pyHydrabus.SWD.sda¶: SDA pin status

pyHydrabus.SWD.timeout¶

pyHydrabus.SWD.wires¶: Raw-Wire mode (2=2-Wire, 3=3-Wire)

pyHydrabus.aux module¶

class pyHydrabus.auxpin.AUXPin(number, hydrabus)¶

Bases: object

Auxilary pin base class

This class is meant to be used in any mode and is instanciated in the Protocol class

Example:

>>> import pyHydrabus
>>> i=pyHydrabus.RawWire('/dev/hydrabus')
>>> # Set AUX pin 0 (PC4) to output
>>> i.AUX[0].direction = pyHydrabus.OUTPUT
>>> # Set AUX pin to logical 1
>>> i.AUX[0].value = 1
>>> # Read Auxiliary pin 2 (PC5) value
>>> i.AUX[1].value

INPUT = 1¶

OUTPUT = 0¶

direction¶

Auxiliary pin direction getter

Returns:	The pin direction (0=output, 1=input)
Return type:	int

pullup¶

Auxiliary pin pullup getter

Returns:	Auxiliary pin pullup status (1=enabled, 0=disabled”)
Return type:	int

toggle()¶: Toggle pin state

value¶: Auxiliary pin getter

pyHydrabus.nfc module¶

class pyHydrabus.nfc.NFC(port='')¶

Bases: pyHydrabus.protocol.Protocol

NFC protocol handler

Example:

>>> import pyHydrabus
>>> n=pyHydrabus.NFC('/dev/hydrabus')
>>> # Set mode to ISO 14443A
>>> n.mode = pyHydrabus.NFC.MODE_ISO_14443A
>>> # Set radio ON
>>> n.rf = 1
>>> # Send REQA, get ATQA
>>> n.write_bits(b'&', 7)
>>> # Send anticol, read ID
>>> n.write(b' ', 0).hex()

MODE_ISO_14443A = 0¶

MODE_ISO_15693 = 1¶

mode¶

rf¶

write(data=b'', crc=0)¶

Write bytes on NFC https://github.com/hydrabus/hydrafw/wiki/HydraFW-binary-NFC-Reader-mode-guide#send-bytes-0b00000101

Parameters:	data (bytes) – Data to be sent

write_bits(data=b'', num_bits=0)¶

Write bits on NFC https://github.com/hydrabus/hydrafw/wiki/HydraFW-binary-NFC-Reader-mode-guide#send-bits-0b00000100

Parameters:	data (byte) – Data to be sent num_bits (int) – number of bits to send

pyHydrabus package¶

Submodules¶

pyHydrabus.hydrabus module¶

pyHydrabus.i2c module¶

pyHydrabus.onewire module¶

pyHydrabus.protocol module¶

pyHydrabus.rawwire module¶

pyHydrabus.smartcard module¶

pyHydrabus.spi module¶

pyHydrabus.Utils module¶

pyHydrabus.uart module¶

pyHydrabus.swd module¶

pyHydrabus.aux module¶

pyHydrabus.nfc module¶

Module contents¶

pyHydrabus

Navigation

Related Topics